Edge Solutions

Workboat Shaft Power Meter — TT50 + ITM Connect

“Wireless torque. Connected fleet — from shaft torque to fleet insight, without a teardown.”

Workboat Torque Monitoring — TT50 + ITM Connect

  • Most boats know how fast their shafts turn. Far fewer know how hard those shafts are working — torque shows what the shaft actually delivers to the propeller.
  • No shaft disassembly or modification: strain gages bond to the prop shaft and the transmitter clamps around it as a collar.
  • Measured shaft horsepower, port and starboard, on the wheelhouse display — not rated or nameplate horsepower.
  • The same picture in the wheelhouse and the office, for one vessel or a whole fleet.
The workboat shaft power meter in 30 seconds.

Workboat Shaft Power Meter App

The TorqueTrak 50 SPM (TT50) from Binsfeld Engineering measures torque, RPM and power on a rotating shaft for long-term monitoring. Strain gages are bonded to the prop shaft, and a battery-powered TX50 Strain Transmitter clamps around it as a link-style collar. The TX50 sends its data over Bluetooth Low Energy directly to ITM Connect — no separate receiver. ITM Connect, an Edge Solution by ITM, is a web app that runs on an ITM Compute edge computer on board, so the analysis happens on the vessel where the data is collected. It calculates shaft power from torque and speed, and does three things with the result at once: shows it live on a wheelhouse display, shares it with the vessel’s other systems, and sends it to shore over LTE or satcom.

The ITM Connect dashboard for a twin-screw workboat: total power, peak torque, shaft speed and devices-online tiles across the top; port shaft and starboard shaft torque gauges and a shaft-speed gauge; a torque trend for the last sixty minutes with both shafts overlaid; and a burst FFT spectrum.
Port and starboard shaft power on the ITM Connect dashboard. Illustration from the overview film; values are illustrative.
  • Port and starboard, side by side — on a twin-screw towboat or tug, a TT50 on each shaft shows both sides of the boat on one screen.
  • Measured shaft power — power is calculated from torque and shaft speed (P = T × ω), giving measured shaft horsepower instead of a rating.
  • Continuous trends — torque, power and RPM recorded once per second, with live values and trends on the wheelhouse display.
  • Bursts and FFT — scheduled high-rate bursts are analyzed by FFT, so a problem that repeats with every revolution or every gear tooth stands out as a peak.
  • Shaft order tracking — eccentricity, misalignment and propeller blade pass sit at fixed shaft orders whatever the speed, so they can be trended and alarmed.
  • Shares it on board and ashore — Modbus, EtherNet/IP, MQTT and web services on the vessel; LTE or satcom to shore. It runs unattended, with no engineer needed aboard.

At a glance: Fits shafts from 65 mm to 1 m or larger · IP66 transmitter, −40 to 70 °C · about a year on its battery, depending on settings · Bluetooth Low Energy direct to ITM Connect · 1 Hz trends plus high-rate FFT bursts · LTE or satcom to shore.

Measured shaft power is the differentiator. A tachometer shows speed, not load. Torque is the number behind how a boat performs on a tow, how its gear wears, and what its engines are really being asked to do. Order tracking then turns the same collar into a diagnostic instrument: eccentricity, misalignment and propeller blade pass each hold a fixed shaft order as speed changes, so a developing fault becomes a trend and an alarm instead of a surprise in the yard.

A bar chart of torque by shaft order from one to twelve at 600 rpm, with labelled peaks at order one for eccentricity, order two for misalignment and order four for propeller blade pass.
Shaft orders hold their place as speed changes (illustration)

TorqueTrak and the TT50 are products of Binsfeld Engineering Inc.

One measurement. Three views.

What measured shaft power is worth depends on your job. The same collar, the same wireless link and the same app serve the office, the engine room and the shipyard — so the question is not whether the shaft can be measured, but who needs the number. Read: Wireless Torque. Connected Fleet. — ITM at the International WorkBoat Show 2026 →

Cutaway drawing of a tug: a TorqueTrak 50 SPM collar on the prop shaft between the main engine and propeller sends torque wirelessly to ITM Connect and on to the wheelhouse HMI.

Owners and operators

See shaft power and torque trends for one vessel or a whole fleet, from shore. You can see how each boat is being worked without waiting for a call from the wheelhouse.

Reads — measured shaft horsepower and torque trends, per shaft and per vessel.

Used for — fleet oversight, and records: measured shaft power can support EEXI power records and USCG Subchapter M record-keeping for U.S. towing vessels.

A prop shaft running between an engine and a gearbox with the TorqueTrak 50 SPM collar by Binsfeld Engineering clamped on in place.

Engineers and crews

Port engineers, chief engineers and crews get early warning of drivetrain problems, so they can be checked before they become expensive failures.

Reads — live torque, RPM and power, with FFT and shaft-order results from every burst.

Used for — catching propeller damage, misfire, gear mesh issues and bearing trouble early.

Signal flow from the TT50 collar over Bluetooth LE to ITM Connect at the edge, then to Modbus, EtherNet/IP, MQTT services and web services.

Shipyards, naval architects and OEMs

Real load data for the people who build, repair and repower boats, taken from the shaft itself and available on board or ashore.

Reads — torque, speed and power through the driveline under real operating conditions.

Used for — sea trials, commissioning and troubleshooting, and checking propulsion performance after a repair or repower.

Beyond the shaft

Torque is where it starts, not the whole product. ITM Connect is expandable with other wireless sensors across the drivetrain, including vibration, temperature, fuel flow and GPS, so shaft torque monitoring sits alongside the rest of the picture. For the collar, the app and the torque, thrust and bending measurements in detail, see Torque Monitoring — TT50 + ITM Connect.

See it running: ITM and Binsfeld Engineering are at the International WorkBoat Show in New Orleans, December 2–4, 2026, booth #2240. Read the post →

“From Shaft to Cloud” program with Binsfeld Engineering; marine prop-shaft analytics reports in production.

Next step: start with one shaft, then make it permanent.

Talk to an engineer: (844) 837-8797 · info@iTestSystem.com

Related Edge Solutions resources